Ergonomically designed, all steel construction, left hand drive cabin with adjustable seat that is fully thermal and noise insulated. Instrumental panel with gauges. Warning and indicator lamps. All controls and levers are located for ease of operation. Automotive safety glass all round for maximum operator protection.Main Specifications of BG D32 Model KBZK D32 N.V.W 21000kg Payload 32000kg G.V.W 53000kg Overall dimensions(LxWxH) 7496x3710x3670MM Wheel bass 3350mm Track Front:2680mm Rear 2350mm Top speed 50km/h Max.gradeablity 35% Min.turning radius ≤8.5m Engine Model Cummins M11-C330 Max.power 246Kw/2100r/min Max.torque 1458Nm/1300r/min Clutch 15"Double-plate dry clutch Transmission Eaton MRT-12710B Gear 1 2 3 4 5 6 7 8 9 10 Lo.rev Hi.rev Ratio 14.78 11 8.17 6 4.46 3.31 2.46 1.83 1.34 1 3.38 15.1 Rear axle With wheel hubs reductions Total ratio:11.86:1 Steering Full hydraulic steering system Working pressure:12.25MPa Brakes Double circuits,pneumatic control brakes system working pressure:(690-820)KPa Suspension Nitrogen/oil suspension units Body hoist Tipping and falling time≤14sec. Body capacity Struck:16 m 3 Heaped(SAE2:1):21M 3 Tyres: 18.00-25 Electrical system voltage 24V ENGINE Model: Cummins M11-C330Style: In line 6Cyl.four-cycle water cooled diesel engineAspiration: turbochargedBore and stroke 125x147mmDisplacement 10.8LMax. power 246Kw/2100r/minMax. torque 1458N.m/r/minTotal mass(with standard accessory) 981kg CLUTCH 15" double-plate dry clutch,pedal contro,hydro-pneumatic assistor. TRANSMISSION Eaton MRT-12710B.Double transmiting shafts in main and sub box. FRONT AXLE Independent air over hydraulic piston suspension.Suspension pisons serves as king pins.Caster angle 0°Kin pin angle 6°Camber angle 1.5°Toe-in (0-6.5)mm DRIVE AXLE Main reduction with heavy duty single stage spiral bevel gear.Reduction ratio 2.4:1Hubs reduction with 3 planetary gear reduction system.Ratio 4.94:1Axle shaft Full-floatingTotal reduction ratio of rear axle 11.86:1 STEERING Type:Full hydraulic power steering system with adjustable height and incination steering wheel column.Actuation:two double acting hydraulic cylinders and shock absorbers to cushion shock loads acting on the steering system during operation.Emergency steering:24 volt DC motor driver gear pump will provided hydraulic pressure for steering system in the event of engine or engine driven hydraulic pump failure for steering system in the event of engine or engine driven hydraulic pump failure for 10 minutes.Working flow and pressure:engine driven vane pump with a flow rate of 23 L/min(at engine speed of 1400 rpm)and hydraulic pressure of 12250KPa. BRAKES Service Dual circuit pneumatic drum brake.Retarder Jacob brakes system fitted to engine.Working pressure (680~820)KPa SUSPENSION Independent air over hydraulic suspension units on front wheels and air over hydraulic units on rear axle.Front suspension cylinders bolted and keyed directly onto chassis..Pistons act as front wheel king pins maintaining correct degree of camber.Front suspension: Inflating pressure 1300KPa Refill oil capacities (6.3x2)LRear suspension: Inflating pressure 1300KPa Refill oil capacities (3.3x2)L BODY HOIST Twin three stage double acting cylinders mounted on the outer chassis frame.Max. working pressure 15300KPa flow 155L/minHigh pressure fine filter 15 micron flow 300L/minMax. tipping angle 47°Tipping time of body ≤14secFalling time of body ≤14sec FRAME Fabricated from high tensile steel and cast iron members at critical points.Main chassis frame members are of box section construction. CABIN Ergonomically designed,all steel construction,left hand drive cabin with adjustable seat that is fully thermal and noise insulated.Instrumental panel with gauges.warning and indicator lamps.All controls and levers are located for ease of operation.Automotive safety glass all round for maximum operator protection. DUMP BODY The body of wedge profile assures a quick clean discharge.Body plate and under floor ribs are manufactured from high yield point steel.A body prop is standard enabling the body to be safely retained for maintenance. TYRES Standard of tyres 18.00-25Rim size 13.00x25Pressure Front wheel (550±20)KPa Rear wheel (625±20)KPa ELECTRICAL SYSTEM Single cable,negative ground,voltage rating 24V.
