BXM2822A1y Auto Solar Module Laminator

1) PLC+TOUCHED LCD controlled auto solar module laminator. Laminating area size: 2800*2200mm. Capacity: 7.5MW (2) Heating system includes 1 unit PID controller, 1 PCS heating steel plate with size: 3000*2400*58mm, oil tubes, heat transfer oil, oil heating station with safety certificate. Max working pemperature: 180 degree C, we suggest: Working temperature range: 120~150 degree, at this range, temperature uniformity: ± 1.5DEGREE, temperature control accuracy: ± 1 DEGREE ( after amending) (3) Special transfer system, modules can be transferred to the laminating area frame by frame. This will cause less movement and broken. Broken less than 0.1%. (4) Cooling fan at the output area can cool the laminated solar modules with fresh air. This will match the product line especially the sun simulator for testing the solar module with temperature range 0~80 degree C ( THE SUN SIMULATOR CAN EMEND AND CALCULATE AUTO MATICALLY to the data as at temperature 25 degree ) (5) It has password for the operator, through this password, all the parameters including: Tank temperature, heating plate temperature, vacuum time, lower chamber air charging time, 1st laminating time, 2st laminating time etc, can be set on the touched LCD. And the cycle can be counted automatically. Both the setting data and the real data can be shown on the screen. It will cause less broken for laminating in two times not in one time. (6) Alarm system: A: It will "NOTICE" if the real temperature is not more than 120 degree when you want to start the laminating and will alarm if the temperature is not more than 120 degree when it is laminating. B: It will alarm if if the real temperature is 10 degree higher than setting. C: It will alarm if the vacuum inside the lower chamber can not reach the setting data in 2 minutes when vacuum the lower chamber. D: It will alarm 1 minute before opening the cover, in this one minute, you may press " PAUSE". This is for placing the solar module onto the correct area. E: There is one oil level gauge in the OIL HEATING STATION. It will alarm if the level is lower than setting, check if any oil leakage, then add oil, it will not alarm. (7) Maintenance Notice A: It will shown on the screen, you should change the HEAT TRANSFER OIL ( 1 year 1 time, model: Mobil Termia 603 ) B: It will shown on the screen for you to change the SILICON MEMBRANE and the silicon slat ( 1 PCS every 1500 cycles). C: It will shown on the screen for you to change the VACUUM PUMP OIL ( every 1500 hours) (8) With 1 PCS Rotary vacuum pumps( model: 2X70), vacuum speed: 70L/S, real vacuum can be 30~50Pa. (9) Safety design: A: Cover closing alarm. With one unit of light protecting system and wall protecting system, it will alarm and stop the cover closing if some one go inside the setting area when the cover is closing. B: Oil tubes between the heating plate and the oil station, are packaged by special cloth to prevent the hurt. C: The two cylinders for cover opening and closing are lockable, even the power shut down or pressure air shut off, the cover will not come down suddenly. D: There is EME cover opening system. When the laminating is going on, the cover can be opened even the power is shut off. E: The machine foot is special designed to prevent earth quake. (10) Power supply: 380Vac/50Hz, 60KW. Ever age power cost: About 35KW. (11) Pressure air supply: 0.7~0.9MPa. Speed: 0.4~0.8 M3/Minnute (12) Dimension: A: Main body: 980CM(L), 290CM (W), 195CM (H) B: Heating Station: 165 CM (L), 60CM (W), 160CM(H) C: Vacuum station: 130 CM(L), 90 CM(W), 150CM(H) (13) Weight: Total: 13T, Laminating part: 9 T (14) Power supply: 380VAC, 50 Hz, 50Kw, 3 phases 5 wires. Working power: 28~32 KW